given load造句
例句与造句
- In solving most stress problems it is first necessary to find the reactions that the given loading produces .
在解决多数的应力问题时，首先必须求出已知载荷产生的反力。 - With the network , the effects of low - loading strengthening can be determined under given load and times of strengthening
对于给定的强化载荷和强化次数，应用构造的神经网络模型，可以确定相应的低载强化效果。 - This returns the given loaded config variable value . if no parameter is given , an array of all loaded config variables is returned
返回指定配置变量的值。如果不指定变量名称，则会返回一个包含所有已加载配置变量的值的数组。 - First , the paper designs the loading system on the basis of given loading data . then , it sets up the linear model of simulation and simulate
本文首先进行起落架加载系统的静态参数设计并建立其线性化仿真模型，然后进行仿真。 - You should generally run several runs with different step durations and step user counts so that you can get good measurements for a given load
通常应运行具有不同的单步持续时间和单步用户计数的几个运行，这样在给定的负载下可以准确地衡量。 - It's difficult to find given load in a sentence. 用given load造句挺难的
- This returns the given loaded config variable value . if no parameter is given , an array of all loaded config variables is returned
此函式在传回由组态档载入的变数值。如果没有使用任何参数的话，则所有经由组态档载入的变数都会以阵列的形式传回。 - First , the loading system is designed on the basis of given loading data . then , the linear model of simulation is set up and simulated
首先根据用户给定载荷及要求对系统进行设计，然后根据初步设计建立系统仿真模型，对多余力和加载曲线进行仿真。 - 3 , analyzing the stress field of the aero - engine case under the given loads , the fatigue life of the case is predicted through the presented fatigue model and the method of " nominal stress "
用该模型对孔径为5mm层合板的s ? n曲线进行疲劳寿命预测及试验验证。 3 、首次对某型发动机t300 kh - 304复合材料机匣的主铺层在给定工况下的疲劳寿命进行预测。 - According to the behaviors of diagonally - loaded frames , effects of infill material property and frame stiffness on performance of infilled frames are investigated . 2 . based on result of lateral actions test , gives load - deflection curves for infilled frames
对斜向加载的墙板单元进行了试验研究，分析了填充块材料性能、框架梁柱刚度等因素对墙板单元力学性能的影响。 - Based on the six - port relative power theory that for a given load the relative power ratios of different ports are left unchanged with the input power to the six - port varied , characteristic parameters of detectors can be obtained through the least - square method
根据六端口相对功率理论即对某一负载各端口相对功率比值不随输入功率变化，由最小二乘法得到检波器的特征参数，结合四标准法，确定六端口网络的系统常数。 - The following work has been done in this paper : the load characteristic and design calculation method of spring are systematically studied . the method of using assembled springs to simulate flexible joint is presented , and then the structural configuration of simulation joint is given . the method above - developed can be used to calculate the parameters of the simulation joint on the given load and displacement conditions
主要内容包括以下几个方面：从弹簧的受力特性出发，系统地研究了弹簧的受力及设计计算方法；通过受力特性分析，提出了采用弹簧组合的形式来模拟柔性接头的设计方法，并给出了模拟接头的设计形式；结合理论方法，开发了能够用于给定载荷和位移条件下计算所需模拟接头参数的应用软件，并给出了模拟接头参数设计的算例。 - The main function of a governor is to monitor the speed deviation of a hydro turbine unit and convert it into the displacement deviation of the servomotor according to a specific characterisic . it is used to control the opening of the guide apparatus and to ensure the unit run steadily at fixed speed under a given load
调速器的主要功用是检测机组转速偏差，并将它按一定特性转换成接力器的行程偏差，借以调整机组导水结构的开度，使机组在给定的负荷下以给定的转速稳定运行。